红狮PRS11032

CUB5B000PAXCDS10PAXD0010PAXP0010G310S000+G3DN0000PAXCDL10PAXR0000  
CSPID2ROPAXS0000+PAXCDC50PAXS0000+PAXCDC50PAXS0000+PAXCDC50PAXS0000+PAXCDC50 PRS11012/PRS11022/PRS11032红狮PAXI0010PAXS0010PAXI001BPAXS001BPAXS0000+PAXCDC50PAXS0000+PAXCDC50PAXS0000+PAXCDC50PAXS0000+PAXCDC50  PAXSOOOOMP37CA00APLPT510IMI04167IMS03162APLSP4B0GEM20060CUB5B000PAXCDS10  PAXD0010PAXP0010G310S000+G3DN0000PAXCDL10PAXR0000PAXS0000+PAXCDC50PAXS0000+PAXCDC50  CSPID2ROPAXS0000+PAXCDC50PAXS0000+PAXCDC50PAXS0000+PAXCDC50PAXS0000+PAXCDC50  PAXI0010PAXS0010PAXI001BPAXS001BPAXS0000+PAXCDC50PAXS0000+PAXCDC50  
PAXSOOOOMP37CA00APLPT510IMI04167IMS03162APLSP4B0GEM20060CUB5B000  
PAXCDS10PAXD0010PAXP0010G310S000+G3DN0000PAXCDL10PAXR0000  
CSPID2ROPAXS0000+PAXCDC50PAXS0000+PAXCDC50PAXS0000+PAXCDC50PAXS0000+PAXCDC50  PAXI0010PAXS0010PAXI001BPAXS001BPAXS0000+PAXCDC50PAXS0000+PAXCDC50  
网络隔离：在Profibus网络和传感器及用户输入公共端之间，500Vrms1分钟。  
类型模块系列说明产品序列号  
选项卡PAXCDS双路设定点C型继电器输出卡PAXCDS10  
四路设定点A型继电器输出卡PAXCDS20  
PRS11012/PRS11022/PRS11032红狮    四路设定点NPN 晶体管输出卡PAXCDS30  
四路设定点PNP晶体管输出卡PAXCDS40  

PAXCDCRS-485串口通信卡（接线端子台式）PAXCDC10  
RS-485串口通信卡（RJ11接口式）PAXCDC1C  
RS-232串口通信卡（接线端子台式）PAXCDC20  
RS-23串口通信卡（RJ11接口式）PAXCDC2C  
DeviceNET总线通信卡PAXCDC30  
PRS11012/PRS11022/PRS11032红狮   Modbus串口通信卡（接线端子台式）PAXCDC40  
Modbus串口通信卡（RJ11接口式）PAXCDC4C  
Profibus-DP总线通信卡PAXCDC50  
PAXCDL模拟量输出卡（0/4-20ma,0-10VPAXCDL10  
PAXLBK工作单位标签（PAXT不需要）PAXLBK10  
SFPAXCrimson2.0配置软件）SFPAX  
模拟量输出卡（0/4-20mA;0-10V）  
Profibus-dp卡  
总线类型：根据EN50170的Profibus-DP,和西门子的SPC3ASIC配合使用  
适应性：符合PNO的Profibus-dp从站装置  
波率特：自动检测波率，在9.6K波率特和12M波率之间  
站地址：0-126，有主机通过网络设定，地址存储在非易失性的内存中  
连接：9针D形母头  
网络隔离：在Profibus网络和传感器及用户输入公共端之间，500Vrms1分钟。  
定时/时钟PAXCK000PAXCK010  
PAXTM000PAXTM010  
1.显示：5位，14.2mm红色日光下可读或绿色LED（-19999到99999）  
2.电源：AC电源型：电源：85-250VAC,50/60HZ,15VA,隔离：2300Vrms/1分钟，输入输出间的隔离  
DC电源型：（不适用于PAXH）DC电源：11-36VDC,11WAC电源：24VAC,±10%，50/60HZ,15VA  
隔离：500Vrms/1分钟，输入输出间隔  
PRS11012/PRS11022/PRS11032红狮3.指示符：MAX-最大读数选择MIN-最小计数选择TOT-累加计数选择，当累加值溢出时闪烁  
SP1-设定点报警1触发SP2-设定点报警2触发SP3-设定点报警3触发SP4-设定点报警4触发  
单位标签-可选工程单位标签，背光显示。  
4.按键：共有5个按键，其中3个可编程功能键  
5.A/D转换器：16位精度  
6.更新率：A/D转换速率：20次/秒显示更新率：1-20次/秒设定点输出开/关延时：0-3275秒  
PRS11012/PRS11022/PRS11032红狮模拟量输出更新率：0-10秒最大/最小捕捉延时：0-3275秒  
7.显示信息：OLOL-当测量值大于上限时显示ULUL-当测量值小于下限时显…-当显示值大于显示上限时显示